Saudi Arabia 10x30m Projection Film Project: 7 Rolls of 1.524x30m Rear Projection Transparent Film Solution
2026-11-17
Project Background
A client based in Saudi Arabia approached our team with a large-format projection requirement: an immersive display surface measuring 10 m wide by 30 m long, a total of 300 m². The site sits in a hot, dusty environment where high ambient temperature and strong light demand a film with stable dimensions and careful installation practice. The client had already collected quotations from several suppliers, but most quoted a square-metre price without explaining how standard roll widths map onto a 10 x 30 m layout — the point at which most projection film projects run into trouble.
Requested Specification vs. Standard Roll Size
| Item | Client Requirement | Our Standard Roll |
|---|---|---|
| Finished coverage | 10 m (W) x 30 m (L) = 300 m² | 1.524 m (W) x 30 m (L) = 45.72 m² per roll |
| Roll width | 10 m total width | 1.524 m (60 inch) |
| Roll length | 30 m total length | 30 m — matches the site length exactly |
Sizing Calculation: Why We Recommended 7 Rolls
Because our standard roll length of 30 m matches the site length exactly, the whole installation can be planned as seven full-length vertical panels, so there is no horizontal joint across the projected image.
| Calculation Step | Formula | Result |
|---|---|---|
| Minimum rolls by width | 10 m ÷ 1.524 m | 6.56 rolls — 6 rolls is not enough |
| Recommended quantity | Round up to the next whole roll | 7 rolls |
| Total width supplied | 7 x 1.524 m | 10.67 m (0.67 m trim allowance) |
| Total area supplied | 7 x 45.72 m² | 320.04 m² |
| Waste ratio | 320.04 m² against 300 m² required | approximately 6.7% |
Six rolls would cover only 9.14 m of the 10 m width, leaving a dark strip of about 0.86 m along one edge. Seven rolls give 10.67 m of total width, so the installer can overlap and trim roughly 0.33 m at each outer edge, cut clean straight borders, and still finish with exactly 10 m of usable surface.
Product Recommendation: Rear Projection Transparent Film
For this project we recommended our rear projection transparent film, a self-adhesive optical film designed for back projection but which can also be used in a front projection setup. Used as a front projection screen, the gain and contrast are naturally lower than in true rear projection — the image is slightly dimmer and more dependent on ambient light control. However, the material cost is dramatically lower than that of a dedicated transparent front projection film, and for this client's viewing distance and lighting conditions the result was more than acceptable.
| Comparison | Rear Projection Transparent Film (recommended) | Dedicated Transparent Film |
|---|---|---|
| Primary use | Rear projection, dual-use as front projection | Front projection only |
| Front projection performance | Good, slightly lower gain and contrast | Higher gain and contrast |
| Material cost | Substantially lower | Significantly higher |
| Transparency / see-through effect | Yes, with the film switched off | Yes |
| Best fit | Large surfaces with controlled lighting and budget discipline | Premium retail windows and high-brightness front projection |
To remove any doubt before ordering, we sent the client real sample photos of this film working as a front projection screen, so the brightness, colour rendering and viewing angle could be judged before committing to 320 m² of material. After reviewing the samples, the client confirmed that the performance was acceptable and approved the recommendation.
Installation Advantages of the Seven-Roll Layout
- Zero horizontal joints — each panel is a continuous 30 m run, so no seam cuts across the middle of the image.
- Only six vertical seams — far fewer than a layout built from shorter rolls, cutting both labour hours and visible joints.
- Controlled trimming — 0.33 m trimmed from each outer edge allows precise alignment and absorbs small frame deviations.
- Damage buffer — the 6.7% allowance covers accidental damage during transport or installation, a realistic risk on dusty outdoor sites.
Handling Notes for Hot, Dusty Climates
Rolls should be stored shaded and never left in direct sunlight before application. The film should be installed when surface temperature is moderate, ideally early morning or evening, and the wall must be cleaned free of dust and sand beforehand — grit trapped under the film shows as a bright spot in projection.
Project Outcome
The client accepted the seven-roll plan together with the rear projection transparent film recommendation, avoiding both a width shortfall and the high cost of dedicated transparent film. The full 10 x 30 m surface is now covered by seven full-length panels, delivering a uniform image for advertising, events and immersive display use at a materially lower project cost.
Planning a Projection Film Installation?
Send us your finished width and length and we will return a roll-by-roll cutting plan, a seam layout and a full material list within one working day. Standard 1.524 x 30 m rolls are available from stock, and custom widths can be produced to order.